Turbochef-technologies TurboChef User Manual Page 29
- Page / 94
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
USER CONFIGURABLE OPTIONS - ENABLE/DISABLE CODES
The following codes enable and disable each function/screen listed. They do not take you to the function/screen.
After each code, press
ENTER. To enable, press 9 after entering code (except S-A-V-E, W-A-V-E). To disable, press
any key (except 9) after entering code.
Function/Screen Simultaneously Press Enter Key Code
Done Screen w/out “Save Time”
BACK & ENTER 3-6-6-3 (D-O-N-E)
Done Screen w/ “Save Time” - step 1
BACK & ENTER 3-6-6-3 (D-O-N-E)
Done Screen w/ “Save Time” - step 2
BACK & ENTER
8-4-6-3 (T-I-M-E)
Edit Recipe Mode
UP & DOWN 8-4-3-3 (T-I-D-E)
Load Menu from Card
BACK & ENTER 6-3-6-8 (M-E-N-U)
Save Menu to Card - step 1
BACK & ENTER 6-3-6-8 (M-E-N-U)
Save Menu to Card - step 2
BACK & ENTER 7-2-8-3 (S-A-V-E)
Snooze Screen
BACK & ENTER 7-6-6-9 (S-N-O-Z)
Time Screen (Figure 16)
BACK & ENTER 8-4-6-3 (T-I-M-E)
Timed Mag Test
BACK & ENTER 9-2-8-3 (W-A-V-E)
- Some codes are not available on some ovens.
- Oven must be in Off or Cooling Down mode.
USER CONFIGURABLE OPTIONS - ACCESS CODES
The following codes allow access to each function/screen listed. To enable/disable these codes (where applicable),
see above. After each code, press
ENTER.
Function/Screen Simultaneously Press Enter Key Code
Edit Recipe Mode
UP & DOWN 9 (or as specified - see “Set PIN” below)
Erase Menu*
BACK & ENTER 3-7-2-7 (E-R-A-S)
Load Menu from Card Bottom-left, then upper-mid soft key
Master Reset
BACK & ENTER 9-4-7-1
Save Menu to Card Bottom-left, then lower-mid soft key
Set PIN**
UP & DOWN 3-3-4-8 (E-D-I-T)
Test Mode
BACK & ENTER 9-4-2-8 (W-H-A-T)
Unit Test
BACK & ENTER 8-6-4-8 (U-N-I-T)
View Cook Counts 1 & 3
View Faults*** 4 & 6
Zero Cook Counts*
BACK & ENTER 6-7-3-9 (O-R-E-Z)
- Oven must be in Off or Cooling Down mode.
* To execute, press 3 after entering code.
** Set PIN after entering code. Accessing “Edit Recipe Mode” will now require new PIN instead of 9.
*** To view voltage, press ENTER. To initiate a self test, press the corresponding soft key from the voltage screen.
19
THE CONTROL SYSTEM
- TurboChef Service Manual 1
- For further information call: 2
- +1 214.379.6000 2
- NEVER attempt to 3
- Table of Contents 4
- IMPORTANT SAFETY INSTRUCTIONS 7
- GENERAL SAFETY INFORMATION 7
- REDUCING FIRE RISK 7
- EXCESSIVE MICROWAVE ENERGY 8
- GROUNDING INSTRUCTIONS 8
- POWER CORD REPLACEMENT 8
- 1 year parts and labor 10
- VAC, 60 Hz, 1 phase 10
- 4” (102 mm) adjustable legs 10
- 304 stainless steel line 10
- POWER INPUT 11
- TURBO / +1 214.379.6000 13
- 1 2 3 4 5 14
- Theory of Operation 15
- THEORY OF OPERATION 16
- CONTROL SYSTEM 16
- MICROWAVE SYSTEM 16
- CONVECTION SYSTEM 16
- BOTTOM IR AND CCV 16
- Fault Codes 19
- TO VIEW FAULT CODES 20
- FAULT CODE DEFINITIONS 20
- FAULT CODES 21
- The Control System 22
- CONTROL 23
- TEST MODE 24
- TEST FUNCTION OPTIONS 25
- W) status indicator is not 26
- DIAGNOSTIC MODE 26
- (CCSP) 26
- THE CONTROL SYSTEM 27
- FIGURE 15: Done Screen 28
- CONTROL SYSTEM PANEL PARTS 30
- ISSUE RESOLUTION 31
- 800.90TURBO 33
- The Microwave System 34
- MONITOR CIRCUIT DESCRIPTION 35
- MICROWAVE SYSTEM PARTS 36
- THE MICROWAVE SYSTEM 37
- MICROWAVE SYSTEM COMPONENTS 38
- WAVE GUIDE COVER REPLACEMENT 39
- WAVE GUIDE REPLACEMENT 40
- REPLACEMENT 40
- FIGURE 24: High Voltage Diode 42
- FIGURE 25: Magnetron 42
- The Oven Door 47
- OVEN DOOR PARTS 48
- ADJUSTING THE OVEN DOOR 49
- ADJUSTMENTS AND PARTS 50
- MONITOR SAFETY SWITCH PARTS 51
- = 0.020” 51
- Old Switch Setup 52
- New Switch Setup 53
- FIGURE 35: Oven Door Assembly 55
- PART TORQUE 56
- SCREW TORQUE CHART 56
- The Convection Circuit 58
- CONVECTION CIRCUIT COMPONENTS 59
- THE CONVECTION CIRCUIT 60
- IR Element and Catalytic 63
- Converter 63
- COMPONENTS 64
- Schematics and Schematic 66
- Components 66
- SCHEMATIC PARTS 67
- TEST POINT LOCATIONS 67
- I/O BOARD SCHEMATIC 68
- 41: NGC (Tornado) Schematic 69
- NGC (UK) SCHEMATIC 70
- 43: NGCEW (Tornado) Schematic 71
- 44: NGCED (Tornado) Schematic 72
- NGC (BRAZIL) SCHEMATIC 73
- Service Parts and 74
- Illustrations 74
- FILAMENT AND 79
- HIGH VOLTAGE 79
- TERMINALS 79
- APPLY HI-TEMP 81
- GREASE TO AREA 81
- FIGURE 35: OVEN DOOR ASSEMBLY 83
- TURBO or +1 214-379-6000 85
- Comprehensive Part List 89
- ITEM DESCRIPTION 90
- +1 214-379-6000 94
Related products and manuals for Microwaves Turbochef-technologies TurboChef
(34 pages)© 2020, manymanuals.com. All rights reserved. | 0.203 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals