Turbochef-technologies TurboChef User Manual Page 14
- Page / 94
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLATION, SPECIFICATIONS, AND MAINTENANCE
5
DAILY MAINTENANCE FOR THE NGC
Before cleaning, check with the store for custom
cleaning instructions.
When cleaning the oven, use only TurboChef Oven
Cleaner. Any other cleaning products can damage
critical parts and may void warranty on those parts.
Supplies and Equipment
TurboChef Oven Cleaner (P/N 103180 USA,
103380 Intl), Oven Guard (P/N 103181 USA,
103381 Intl), nylon scrub pad, cleaning towel
Step 1: Prepare the Oven
Turn oven off by pressing the BACK key.
The oven will display OVEN OFF/COOLING DOWN.
x
DO NOT attempt to clean oven during the cool
down cycle. Cooling takes appx. 90 minutes.
WARNING: The oven operates at appx. 500
º
F
(260
º
C) and may cause injury if not allowed
time to cool properly.
Step 2: Remove the Lower Access Panel
Wipe out any crumbs that have collected.
Step 3: Remove and Clean the Cooking Surface
If rack, wash, rinse, and sanitize.
If baking stone, gently dry-scrub with nylon pad.
If the stone gets wet, let it thoroughly air-dry.
Step 4: Lift Bottom Element
Be sure the bottom element is cool prior to lifting.
WARNING: The bottom element operates at
appx. 1000
º
F (537
º
C).
Step 5: Remove Particles and Spray Oven Interior
with TurboChef
®
Oven Cleaner
Using a damp towel, remove large food particles.
If stubborn stain is present, sparingly spray
TurboChef Oven Cleaner onto the stain.
Allow cleaner to penetrate for five (5) minutes.
x
DO NOT saturate the bottom of the oven with
water or oven cleaner.
Step 6: Clean Oven Interior
Using a nylon scrub pad, clean the oven door
and cook cavity.
CAUTION: DO NOT apply pressure to the
wave guide covers. Breaking will result in a
non-warranty service call.
Step 7: Wipe Out Oven Interior
Wipe oven door, bottom element, and cook
cavity using a damp towel.
Step 8: Clean Lower Access Panel Area
x
DO NOT spray any chemical in this area.
Step 9: Lower the Bottom Element and Reinstall the
Cooking Surface and Lower Access Panel
Step 10: Apply Oven Guard and Clean Oven Exterior
Spray Oven Guard on towel. Wipe sides of cook
cavity and inside of door.
x
DO NOT
spray Oven Guard directly into cook
cavity or wipe on nozzle plates/bottom element.
Wipe the oven exterior with a clean, damp towel.
Oven is ready to turn on.
10
9
876
1 2 3 4 5
- TurboChef Service Manual 1
- For further information call: 2
- +1 214.379.6000 2
- NEVER attempt to 3
- Table of Contents 4
- IMPORTANT SAFETY INSTRUCTIONS 7
- GENERAL SAFETY INFORMATION 7
- REDUCING FIRE RISK 7
- EXCESSIVE MICROWAVE ENERGY 8
- GROUNDING INSTRUCTIONS 8
- POWER CORD REPLACEMENT 8
- 1 year parts and labor 10
- VAC, 60 Hz, 1 phase 10
- 4” (102 mm) adjustable legs 10
- 304 stainless steel line 10
- POWER INPUT 11
- TURBO / +1 214.379.6000 13
- 1 2 3 4 5 14
- Theory of Operation 15
- THEORY OF OPERATION 16
- CONTROL SYSTEM 16
- MICROWAVE SYSTEM 16
- CONVECTION SYSTEM 16
- BOTTOM IR AND CCV 16
- Fault Codes 19
- TO VIEW FAULT CODES 20
- FAULT CODE DEFINITIONS 20
- FAULT CODES 21
- The Control System 22
- CONTROL 23
- TEST MODE 24
- TEST FUNCTION OPTIONS 25
- W) status indicator is not 26
- DIAGNOSTIC MODE 26
- (CCSP) 26
- THE CONTROL SYSTEM 27
- FIGURE 15: Done Screen 28
- CONTROL SYSTEM PANEL PARTS 30
- ISSUE RESOLUTION 31
- 800.90TURBO 33
- The Microwave System 34
- MONITOR CIRCUIT DESCRIPTION 35
- MICROWAVE SYSTEM PARTS 36
- THE MICROWAVE SYSTEM 37
- MICROWAVE SYSTEM COMPONENTS 38
- WAVE GUIDE COVER REPLACEMENT 39
- WAVE GUIDE REPLACEMENT 40
- REPLACEMENT 40
- FIGURE 24: High Voltage Diode 42
- FIGURE 25: Magnetron 42
- The Oven Door 47
- OVEN DOOR PARTS 48
- ADJUSTING THE OVEN DOOR 49
- ADJUSTMENTS AND PARTS 50
- MONITOR SAFETY SWITCH PARTS 51
- = 0.020” 51
- Old Switch Setup 52
- New Switch Setup 53
- FIGURE 35: Oven Door Assembly 55
- PART TORQUE 56
- SCREW TORQUE CHART 56
- The Convection Circuit 58
- CONVECTION CIRCUIT COMPONENTS 59
- THE CONVECTION CIRCUIT 60
- IR Element and Catalytic 63
- Converter 63
- COMPONENTS 64
- Schematics and Schematic 66
- Components 66
- SCHEMATIC PARTS 67
- TEST POINT LOCATIONS 67
- I/O BOARD SCHEMATIC 68
- 41: NGC (Tornado) Schematic 69
- NGC (UK) SCHEMATIC 70
- 43: NGCEW (Tornado) Schematic 71
- 44: NGCED (Tornado) Schematic 72
- NGC (BRAZIL) SCHEMATIC 73
- Service Parts and 74
- Illustrations 74
- FILAMENT AND 79
- HIGH VOLTAGE 79
- TERMINALS 79
- APPLY HI-TEMP 81
- GREASE TO AREA 81
- FIGURE 35: OVEN DOOR ASSEMBLY 83
- TURBO or +1 214-379-6000 85
- Comprehensive Part List 89
- ITEM DESCRIPTION 90
- +1 214-379-6000 94
Related products and manuals for Microwaves Turbochef-technologies TurboChef
(34 pages)© 2020, manymanuals.com. All rights reserved. | 1.244 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals